Mc-techgroup BA-P4 Operator's manual Manuale Utente

Gas sampling and conditioning technology 10-1.1-ME Instruction Manual Combustion Air Conditioning Unit Series BA Version BA, BA-P4

10 Gas sampling and conditioning technology 10-1.1-ME  Catalytic oxidation Fl3 of the hydrocarbons at a temperature of 500°C on t

11 Gas sampling and conditioning technology 10-1.1-ME 9 DESCRIPTION Figure 2 shows the BA-P4 combustion air conditioning unit. Burner air supp

12 Gas sampling and conditioning technology 10-1.1-ME The catalyst cartridge is installed in a heat-insulated tube furnace. A specia

13 Gas sampling and conditioning technology 10-1.1-ME 10 RECEIPT AND STORAGE The BA... combustion air conditioning unit is a complete, pre-ins

14 Gas sampling and conditioning technology 10-1.1-ME 12 SUPPLY CONNECTIONS 12.1 HOSE CONNECTIONS Connection to the combustion and waste

15 Gas sampling and conditioning technology 10-1.1-ME 12.2 ELECTRICAL CONNECTIONS W A R N I N G ! Incorrect system voltage can damage the

16 Gas sampling and conditioning technology 10-1.1-ME For signalling the group alarm, the contacts 5 and 9 are available in the Sub-D-Plug (see

17 Gas sampling and conditioning technology 10-1.1-ME 14 SWITCH OFF NOTE! The place of installation of the combustion air conditioning uni

18 Gas sampling and conditioning technology 10-1.1-ME 15.1 SWING PISTON COMPRESSOR The swing piston compressor does not need to be removed for

19 Gas sampling and conditioning technology 10-1.1-ME 15.4 CATALYST CARTRIDGE REPLACEMENT Cartridge replacement can take place without the aid

2 Gas sampling and conditioning technology 10-1.1-ME Content

20 Gas sampling and conditioning technology 10-1.1-ME 15.5 ADSORBER CARTRIDGE REPLACEMENT The following steps must be carried out:  Relieve

21 Gas sampling and conditioning technology 10-1.1-ME The inner seals can be removed with a pointed tool (e.g. marking tool). When refitting, t

22 Gas sampling and conditioning technology 10-1.1-ME Heating up Heating flashes Ramp function Sensor control 16 USE OF THE TEMPERATURE CO

23 Gas sampling and conditioning technology 10-1.1-ME 16.3 CHANGING THE PARAMETERS OF THE TEMPERATURE REGULATOR The programming of the regula

24 Gas sampling and conditioning technology 10-1.1-ME 16.4 RESET OF THE CONTROLLER A reset out of the temperature lock happens with connected

25 Gas sampling and conditioning technology 10-1.1-ME 17 TROUBLE SHOOTING The table below is intended to indicate possible causes of faults and

26 Gas sampling and conditioning technology 10-1.1-ME 18 SPARE PART LIST Wear, tear and replacement part requirements depend on specific opera

27 Gas sampling and conditioning technology 10-1.1-ME Figure 5 Circuit diagram BA... with controller 703/70304

28 Gas sampling and conditioning technology 10-1.1-ME Figure 6 Circuit diagram BA... with controller TM48

3 Gas sampling and conditioning technology 10-1.1-ME Dear customer, we have made up this operating manual in such a way that a

4 Gas sampling and conditioning technology 10-1.1-ME Head Office M&C TechGroup Germany GmbH  Rehhecke 79  40885 Ratingen  Germany Tele

5 Gas sampling and conditioning technology 10-1.1-ME 3 SAFETY INSTRUCTIONS Please take care of the following basic safety procedures w

6 Gas sampling and conditioning technology 10-1.1-ME 5 USED TERMS AND SIGNAL INDICATIONS DANGER! This means that death, severe physic

7 Gas sampling and conditioning technology 10-1.1-ME 6 INTRODUCTION The M&C BA... combustion air conditioning unit has been designed speci

8 Gas sampling and conditioning technology 10-1.1-ME 7 FUNCTION Figure 1 shows the function diagram of M&C combustion air conditioning uni

9 Gas sampling and conditioning technology 10-1.1-ME The inlet pressure is maximum 5.8bar and is limited by relief valve YD2 (works setting). Th